✦Template Printable Ideas Insights

Hole Size for 5/16-18 Tap

By

The 5/16-18 tap is a commonly used threaded fasteners system in industrial and manufacturing applications. When selecting a hole size for a 5/16-18 tap, it's crucial to match thedrill diameter to the tap's major diameter for a proper fit and effective thread cutting.

In the standard metric system, a 5/16-inch diameter is equivalent to 7.94 millimeters, which is the major diameter of the 5/16-18 tap. To create a suitable clearance between the tap and the hole wall, the hole size should be slightly larger. Typically, for a 5/16-18 tap, the recommended hole size is between 0.250 and 0.280 inches (or 6.35 and 7.11 millimeters).

Hole Size Calculation for Stress Relief

The hole size also plays a significant role in stress relief and hole preparation. Oversized holes allow the tap to cut threads without exerting excessive pressure on the surrounding material, preventing material deformation and increasing the life of the tap.

V-TapGuide - Standard Tap Sizes, USA Made
V-TapGuide - Standard Tap Sizes, USA Made
a table with numbers and times for different types of items in the form of letters
a table with numbers and times for different types of items in the form of letters
Drill America 5/16"-18 UNC HSS Left 4 Flute Tap Set, Size:5/16"
Drill America 5/16"-18 UNC HSS Left 4 Flute Tap Set, Size:5/16"

A common practice is to use a drill size that's 0.015 to 0.020 inches (0.38 to 0.51 millimeters) larger than the tap's major diameter. For a 5/16-18 tap, this would result in a hole size of 0.275 to 0.295 inches (6.99 to 7.49 millimeters).

Oversizing Holes for Easier Tapping

Oversizing the hole can also facilitate easier tapping, especially in harder materials like steel or cast iron. A larger hole permits the tap to start cutting threads without significant initial resistance, reducing the risk of tap breakage and ensuring cleaner threads.

a table with measurements for the top drill size chart
a table with measurements for the top drill size chart
3/8" Tap Drill Size (Ultimate Guide) - ToolsGaloreHQ
3/8" Tap Drill Size (Ultimate Guide) - ToolsGaloreHQ
Unique Bargains 2pcs Tap and Die Set 3/4-16 UNF Thread Tap and Round Die Tapping Threading Tool Tap and Die Kit for Nut Screw Bolt Thread Repair
Unique Bargains 2pcs Tap and Die Set 3/4-16 UNF Thread Tap and Round Die Tapping Threading Tool Tap and Die Kit for Nut Screw Bolt Thread Repair

A typical oversize for easier tapping with a 5/16-18 tap is up to 0.315 inches (8 millimeters). However, excessive oversizing may lead to weakened material and compromised thread strength, so it's essential to strike a balance based on the specific application and material.

Tolerance Considerations

When selecting a drill size, it's vital to consider manufacturing tolerances. Tighter tolerances ensure a more precise fit and better thread consistency, but they also increase production costs. A common tolerance range for drilled holes is +0.002/-0.005 inches (+0.051/-0.127 millimeters).

To maintain a balance between cost and performance, it's recommended to choose a drill size within the tolerance range that suits the specific application's requirements. For a 5/16-18 tap, a drill size of 0.270 (+0.002/-0.005) inches (or 6.86 (+0.051/-0.127) millimeters) may provide an optimal combination of cost-effectiveness and performance.

23 Printable Tap Drill Charts [PDF] ᐅ TemplateLab
23 Printable Tap Drill Charts [PDF] ᐅ TemplateLab
the table shows different types of drill sizes and decimal equivants
the table shows different types of drill sizes and decimal equivants
four screws are sitting next to each other on top of a notebook with the words tap drill size formula
four screws are sitting next to each other on top of a notebook with the words tap drill size formula
Helicoil tap chart, helicoil tapping chart , helicoil tap size, helicoil tapping size, helicoil
Helicoil tap chart, helicoil tapping chart , helicoil tap size, helicoil tapping size, helicoil
Bolts
Bolts
Milwaukee 5/16 in -18 NC Straight Flute Plug Tap
Milwaukee 5/16 in -18 NC Straight Flute Plug Tap

Drill Size Recommendations Based on Material

The appropriate hole size can also vary depending on the material being tapped. Softer materials may require smaller drill sizes, while harder materials may need larger drill sizes to facilitate easier tapping.

Here are some general drill size recommendations for a 5/16-18 tap based on different materials:

Material Recommended Drill Size (inches) Recommended Drill Size (mm)
Aluminum 0.260 - 0.270 6.60 - 6.86
Brass 0.265 - 0.275 6.73 - 6.99
Steel 0.280 - 0.290 7.11 - 7.37
Cast Iron 0.285 - 0.295 7.24 - 7.49

Adjusting Drill Size for Application-Specific Needs

The recommended drill sizes are meant as a starting point for general applications. However, specific applications may require adjustments based on factors such as:

a measuring tape with the measurements for different sizes and widths on it, as well as
a measuring tape with the measurements for different sizes and widths on it, as well as
Draper Metric Hand Tap Set (10 Piece)
Draper Metric Hand Tap Set (10 Piece)
2pcs Metric Screw Hand Tap and Die Set Fine Thread Dies Taps Suit M4 M5 M6 M7 M8 M9 M10 M11 M12 M13
2pcs Metric Screw Hand Tap and Die Set Fine Thread Dies Taps Suit M4 M5 M6 M7 M8 M9 M10 M11 M12 M13
  • Thread pitch and depth
  • Material thickness and wall strength
  • Thread engagement and load requirements
  • Desired tap life and productivity

It's recommended to perform tests or consult with a tap and die specialist to determine the optimal drill size for application-specific needs.

To ensure long-lasting, effective thread cutting with a 5/16-18 tap, select a drill size that factors in material, stress relief, tapping ease, and application-specific requirements. Regularly monitor and maintain your taps and drilling equipment to preserve tool life and maintain optimal performance.