✦Template Printable Ideas Insights

Drill Size for 3/4" Pipe Tap

By

When it comes to tapping a 3/4 inch (19mm) pipe, selecting the appropriate drill size is crucial for a secure and precise operation. The tap needs to be drilled at exactly the right spot and the hole needs to be of the correct diameter to accommodate the tap’s threads. Here's a comprehensive guide on choosing the correct drill size for a 3/4 inch pipe tap.

Understanding pipe tapping involves knowing that the tap's dimensions correspond with the pipe's nominal size. For a 3/4 inch pipe, the tap chosen would typically be a 7/8 inch (22mm) NPT (National Pipe Thread) tap. But what about the drill size?

Drill Size for 3/4 Inch Pipe Tap

The drill size required for tapping a 3/4 inch pipe will depend on two primary factors: the tap's drill point size, and the pipe's wall thickness.

the drill tap size formula is shown in three different positions
the drill tap size formula is shown in three different positions
a woodworking tool is shown with parts labeled
a woodworking tool is shown with parts labeled
STI Roll Tap Drill Sizes, STI Tap Drill Sizes, and Pipe Tap Drill Sizes
STI Roll Tap Drill Sizes, STI Tap Drill Sizes, and Pipe Tap Drill Sizes

Firstly, consider the drill point size of the tap you intend to use. Most taps, including those for 3/4 inch pipes, come with their own, smaller drill point. This drill point is designed to create a pilot hole that ensures you tap at the right spot and in the right direction.

Using the Tap's Drill Point

If your 7/8 inch NPT tap came with a drill point, you can use this to drill the initial hole. Follow these steps:

6Pc. NPT Pipe Tap Set, 1/8, /1/4, 3/8, 1/2, 3/4, 1", wooden box
6Pc. NPT Pipe Tap Set, 1/8, /1/4, 3/8, 1/2, 3/4, 1", wooden box
a table with measurements for the top drill size chart
a table with measurements for the top drill size chart
Century Drill & Tool Pipe Tap - Pack of 10
Century Drill & Tool Pipe Tap - Pack of 10
  1. Mark the spot where you need to tap.
  2. Using the tap's drill point, carefully drill into the pipe. Typically, drill points are of sizes 1/8 inch or 3/16 inch, suitable for 3/4 inch pipes.
  3. Once you've drilled the pilot hole, proceed to tap the pipe using the 7/8 inch tap.

Using the tap's drill point provides a targeted and controlled starting point for your tapping operation.

Drilling Without a Tap's Drill Point

If your tap doesn't come with a drill point, you'll need to choose a drill bit that creates a pilot hole large enough to accommodate the tap's starting point. For a 7/8 inch NPT tap, a common choice is a 5/32 inch or 3/16 inch drill bit.

Using a drill bit instead of the tap's drill point follows similar steps: mark the tapping location, drill a pilot hole using the drill bit, and then proceed to tap the pipe with the 7/8 inch tap.

the table size chart for drill sizes is shown in red and black, with an arrow pointing
the table size chart for drill sizes is shown in red and black, with an arrow pointing
3/4in-14 NPT HSS 5 Flute Pipe Tap, Left Hand
3/4in-14 NPT HSS 5 Flute Pipe Tap, Left Hand
23 Printable Tap Drill Charts [PDF] ᐅ TemplateLab
23 Printable Tap Drill Charts [PDF] ᐅ TemplateLab
four screws are sitting next to each other on top of a notebook with the words tap drill size formula
four screws are sitting next to each other on top of a notebook with the words tap drill size formula
Pipe Tap, 3/8"-18, 4 Flutes, NPT
Pipe Tap, 3/8"-18, 4 Flutes, NPT
5 Piece Carbon Steel NPT Pipe Tap Set, 1/8", 1/4", 3/8", 1/2" and 3/4", Silver
5 Piece Carbon Steel NPT Pipe Tap Set, 1/8", 1/4", 3/8", 1/2" and 3/4", Silver

Considerations and Best Practices

When drilling into a 3/4 inch pipe for tapping, always ensure the pipe's wall thickness can accommodate the size of your pilot hole and the tap's threads. For standard walls thickness of 3/4 inch pipe, a tap with a proportionate size, like the 7/8 inch NPT, should work fine.

Also, remember to drill slowly and carefully to avoid overheating the pipe and damaging the threads during tapping.

Always double-check your markings, use appropriate safety gear, and make sure the pipe is held securely before drilling and tapping.

2-Piece BSP Pipe Taper Drill Set - 1/2" & 3/4" Internal, External Thread Machine, Single Taper
2-Piece BSP Pipe Taper Drill Set - 1/2" & 3/4" Internal, External Thread Machine, Single Taper
Drill Tap Chart: Complete Guide
Drill Tap Chart: Complete Guide
3/8in-18 NPT HSS 4 Flute Pipe Tap, Left Hand
3/8in-18 NPT HSS 4 Flute Pipe Tap, Left Hand

In conclusion, selecting the right drill size for a 3/4 inch pipe tap primarily involves knowing the drill point size of your tap or choosing a suitable drill bit when no drill point is provided. Following safety protocols and best practices will ensure a successful tapping operation.